The Green document status indicator indicates that the document is: a current in the Construction Information Service and b the latest version - ie it does not have any other documents that replace or amend it and is promoted as a current document by the publisher. The Amber document status indicator indicates that some caution is needed when using this document - it is either: a current in the Construction Information Service but has a document or documents that replace or amend it, so please look at the "Newer Versions" tab or b not in the Construction Information Service but with another reason why it may be relevant to our customers such as being cited in NBS or in the Building Regulations Approved Documents. Again there may be more recent versions of the document. The Red document status indicator indicates that the document is an old version The document has likely been withdrawn by the publisher, also the meta data presented here may be out of date as it is no longer being maintained by the editorial teams at NBS.

Author:Tukazahn Akinogis
Language:English (Spanish)
Published (Last):23 August 2007
PDF File Size:19.92 Mb
ePub File Size:19.18 Mb
Price:Free* [*Free Regsitration Required]

Gardarisar Mechanical properties, screws and studs EN ISO Products conforming to the requirements of this part of Dinn are evaluated only in the ambient temperature range and may not retain the specified mechanical and physical properties at and lower temperatures.

Products in property classes 4. Figure 8 — Examples of marking on hexagon socket head cap screws 9. This European Standard supersedes EN Fasteners, steel products, bolts, screws, studs, specifications, materials specifications, mechanical properties, physical properties, tests, mechanical tests, identification methods, designation, marking.

Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help dim Exporters Service. The property class symbol consists of two figures: Torsional test and minimum torques for bolts and screws with nominal diameter from 1 mm to 10 mm.

If these details are to be used for any dun purpose than implementation then the prior written permission of BSI must be obtained. The abscissae show the nominal tensile strength values, Rm, in newtons per square millimetre, while the ordinates show those of the minimum elongation after fracture, Amin, as a percentage.

For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard cin when incorporated in it by amendment or revision. Values for E are xin in Table The proof load, as given in Table 7 and Table 9, shall be applied axially to the bolt in a tensile testing machine.

Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Table 15 — Clock-face system for marking bolts and screws Property class 3. It is identical with ISO Various BSI electronic information services are also available which give details on all its products and services.

The calculation of the tensile strength, Rm, is based on the nominal stress area As, nom: The minimum lower yield stress ReL, min. The grips of the testing machine should be self-aligning to avoid side thrust on the test piece. For undated references the latest edition of the publication referred to applies.

For details of these and other benefits contact Membership Administration. Where screws are threaded up to the head, the requirements may be considered met even if a crack should appear in the first thread, provided that the head does not snap off.

The work of preparing International Standards is normally carried out through ISO technical committees. Part 1 does not specify properties for fasteners that have head geometries that reduce the shear strength of the fastener, such as low head screws and countersunk heads. The marking is obligatory for all property classes, preferably on the top of the head by indenting or embossing or on the side of the head by indenting see Figure 7.

At temperatures lower than the ambient temperature range, a significant change in the properties, particularly impact strength, may occur. ISO by standard number. A list of organizations represented on this subcommittee can be obtained on request to its secretary. The maximum value for G and the formulae for the minimum value for E are specified in Table 3.

It shall be on the head by indenting or embossing see Figure 9. Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread [2]. The ne of this standard is restricted to bolts and screws of property class 5. When carrying out the test, a minimum free threaded length equal to one diameter 1d shall be subjected to the tensile load.

These values if received from tests of full size bolts and screws will vary because of processing method and size effects. If it is not possible to determine the elongation after fracture due to the length of the bolt, the reduction of area after fracture shall be measured providing that Lo is at least 3 do. The test applies to bolts and screws with nominal thread diameters d u 3 mm as well as to short bolts and screws with nominal thread diameters 3 mm u d u 10 mm which cannot be subjected to a tensile test.

Surface hardness readings taken at HV 0,3 shall be compared with a similar core hardness reading at HV 0,3 in order to make a realistic comparison and determine the relative increase which is permissible up to 30 Vickers points. Principles and basic data. Set screws and similar threaded fasteners not under tensile stresses [4].

ISO consists of the following parts, under the general title Mechanical properties of fasteners made of carbon steel alloy steel: Revisions British Standards are updated by amendment or revision. Before and after the application of the proof load, the bolt or screw shall be placed in a bench-mounted measuring instrument fitted with spherical anvils. Each member body interested in a subject for which a technical committee has been established has the right to be represented on eh committee.

English price group 12 www. TOP Related Posts.


BS EN ISO 898-1:2013



UNE EN ISO 898-1:2015


Related Articles