Print a Printer Settings page to verify the optional sheet tray module or sheet tray module is installed correctly. Chapter 8 Printer Specifications 2. To verify the printer details such as hardware configuration and software version. Remove the protective sheet from the drum cartridge. Do not force print media into the multipurpose feeder when you load it; Code Confirmation procedure 12 Check the sensor. The inside of the printer warms up and condensation evaporates.
|Published (Last):||8 September 2018|
|PDF File Size:||12.3 Mb|
|ePub File Size:||6.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
The printer must be carried horizontally with two or more persons. Extreme care must be taken to avoid personal injuries. Check the printer visually for evidence of any damage. Peel all tapes off the printer. Remove protection parts 2 pieces from the paper tray. After confirming the "Insert Black Toner K " message, open the front door. Hold the tape on the protective cover and pull it forward to remove the cover from each cartridge slot.
You need to remove the protective cover only the first time that you install the toner. Dispose of the protective cover after you remove it. The protective cover is attached to each toner cartridge mount. Make sure the color of the toner cartridge matches the slot on the toner cartridge carrier. The order is K, Y, M, C.
Gently shake the cartridge to distribute the toner evenly. Intro 4. Lift the tab up 90 degrees and pull the toner seal straight off, keeping it parallel with the toner cartridge. To insert the toner cartridges, align the arrows on the cartridge with the corresponding arrows on the printer. Guide the cartridge in until it snaps into place and then push down the handhold to lock the cartridge in place. Close the front door. Make sure the toner cartridge is installed correctly.
Otherwise, the front door cannot close firmly. Intro 7. The toner cartridge carrier rotates to the next empty slot. When the color of the newly inserted cartridge appears on the display, followed by the Insert message, insert the next toner cartridge. Repeat steps 1 through 7 when inserting the remaining cartridges. Intro Installing the Drum Cartridge 1.
When the Insert Drum Cartridge message appears, open the front door, then lift and push back the top cover. Remove the protective sheet from the drum cartridge. To insert the drum cartridge, push up the lever on the right side of the printer. With the lever in the upright position, hold the drum cartridge by the handle, align the arrows on the drum cartridge with the corresponding arrows on the printer and guide the cartridge in until it snaps into place.
Pull down the lever on the right to lock the drum cartridge in place. Close the top cover, then the front door. After installing the drum cartridge, the printer makes an adjustment for about one to two minutes. Do not turn off the printer during this time. Intro Installing the Optional Tray Module If you are adding an optional sheet tray module or sheet tray module after setting up the printer, be sure to turn off the printer, unplug the power cable, and disconnect all cables from the back of the printer before completing these tasks.
Optional sheet tray modules attach under the printer and up to two additional trays can be added. The optional sheet tray module attaches under the optional sheet tray module and only one additional tray can be added. Some instructions may vary depending on the tray module configuration in your printer. Some tray module configurations differ from those described in this manual. Unpack the tray and remove all packing material and tape.
Tray module Tray 2. Place the tray module in the location that you would like the printer to be located. You will place the printer on the tray in a later step. Turn off the printer. If there are any trays already attached to the printer, unlock the tray from the printer by removing the tray from the tray module and turning the locking mechanism, inside the printer, as shown in the graphic. Intro 5. Remove the printer from the tray. Lift the printer with two people, one facing the front of the printer operator panel side and the other facing the back.
Never try to lift the printer while facing its right and left side. Attach the trays together by installing the optional tray you just removed on top and inserting the two screws provided. Tighten the screws with a coin until they are secure.
Place the printer on top of the tray module s. Intro 8. Lock the tray s into place by removing the top tray from the tray module and rotating the locking mechanism as shown in the graphic. Replace all trays and load the paper. Turn on the printer. The printer will automatically detect the attached tray s but will not detect the paper type. Print a Printer Settings page to verify the optional sheet tray module or sheet tray module is installed correctly.
Dell 3010CN User Manual
Monris In order to maintain an appropriate developer concentration, it is necessary to refill with an amount of cm equivalent to that consumed from Toner Cartridge manhal Developer Assy. Installing The Toner Cartridge Adhesive material contaminates your printer and could void your warranty. To specify the type of paper loaded in each tray. You can contact Dell electronically using the following addresses: Chapter 6 Principle s of O peration 8. And you need to check the Copy the delll to the Host in the above list and reboot the machine. Chapter 6 Principle s of O peration 1. Prepare the small paper 10mm x 50mm.
Dell 3000cn Owner's Manual
DELL 3010CN MANUAL PDF